Skip Navigation

Eaton and Tenneco Partner to Produce New, Integrated Exhaust Thermal Management System

LAKE FOREST, Ill., March 25, 2021 /PRNewswire/ -- Power management company Eaton (NYSE: ETN) and Tenneco (NYSE: TEN) today announced a joint development agreement between Eaton's Vehicle Group and Tenneco's Clean Air business group to produce an integrated exhaust thermal management system that will enable commercial truck and light vehicle manufacturers to meet upcoming emissions regulations.

Across the globe, emission standards are tightening for vehicle manufacturers. In Europe, the next stage of emissions standards, known as Euro 7 (for light-duty vehicles) and Euro VII (for heavy-duty), are targeted for introduction in 2025. The California Air Resources Board (CARB) and the U.S. Environmental Protection Agency (EPA) have similar actions planned for 2024 and 2027, respectively. Collectively, these new regulations will reduce tailpipe NOx limits by 90 percent, thus accelerating the need for global engine manufactures to employ additional emission reduction strategies.

Under terms of the agreement, Tenneco's Cold Start Thermal Unit (CSTU) will be combined with Eaton's TVS® blower technology. The integrated exhaust thermal management system will provide heat directly to the vehicle's aftertreatment system, which is essential for reducing harmful exhaust emissions. Upon heating the SCR catalyst to approximately 200 – 250 degrees Celsius, the aftertreatment system can efficiently convert NOx into clean emissions (e.g., nitrogen and water particles) upon exiting the SCR catalyst. Eaton's electrically driven TVS Roots blower allows the airflow to be efficiently and precisely controlled so the CSTU can maintain optimal aftertreatment temperatures. 

"CSTU is an active thermal management technology that rapidly heats and maintains the emission control system temperature," said Nick Morley, director, global advanced engineering, Tenneco's Clean Air business group. "Since the majority of emissions are generated during the initial start of engine operation and during extended idle conditions, the addition of an integrated exhaust thermal management system in front of the catalyst enables rapid light-off and efficient NOx conversion through the full range of operating conditions."

"It became clear about three years ago that future CARB and EPA NOx regulations would be drastically stricter than they are today, and the exhaust thermal management system is an effective technology to actively heat up an aftertreatment system for commercial vehicle diesel engines to dramatically reduce cold-start NOx emissions," said Justin Hopkins, technology development manager, Eaton's Vehicle Group.

"Tenneco is an established leader in the design and development of aftertreatment solutions," said Dmitri Konson, vice president global engineering for Tenneco's Clean Air business. "We are pleased to partner with Eaton to develop a fully optimized system for engine manufacturers, leveraging our aftertreatment technology and engineering capabilities."

The integrated exhaust thermal management system is already drawing attention from several global manufacturers, who are currently selecting which powertrain technology will help them meet future emissions regulations. By adopting this solution complicated multi-injector, light-off catalyst systems, with close-coupled packaging can be eliminated thereby reducing complexity.  The CSTU and TVS blower will be sold individually by Tenneco and Eaton, respectively, but will be engineered as a system enabling vehicle manufacturers to seamlessly integrate the components.

Development activities will take place at Tenneco's technical center in Edenkoben, Germany, and Eaton's technical center in Marshall, Michigan. The integrated exhaust thermal management system is anticipated to be ready for start of production in 2025 to support regulatory timing.

About Eaton

Eaton's mission is to improve the quality of life and the environment through the use of power management technologies and services. We provide sustainable solutions that help our customers effectively manage electrical, hydraulic, and mechanical power – more safely, more efficiently, and more reliably. Eaton's 2020 revenues were $17.9 billion, and we sell products to customers in more than 175 countries. We have approximately 92,000 employees. For more information, visit www.eaton.com

About Tenneco

Tenneco is one of the world's leading designers, manufacturers and marketers of automotive products for original equipment and aftermarket customers, with full year 2020 revenues of $15.4 billion and approximately 73,000 team members working at more than 270 sites worldwide.  Through our four business groups, Motorparts, Ride Performance, Clean Air and Powertrain, Tenneco is driving advancements in global mobility by delivering technology solutions for diversified global markets, including light vehicle, commercial truck, off-highway, industrial, motorsport and the aftermarket. Visit www.tenneco.com to learn more.

This news release contains "forward-looking statements." The forward-looking statements are subject to risks and uncertainties that could cause Tenneco's results to differ materially. All forward-looking statements should be considered in the context of the risk and other factors detailed from time to time in Tenneco's Securities and Exchange Commission filings.

Eaton Contact          
Thomas Nellenbach
thomasjnellenbach@eaton.com
(216) 333-2876 (cell

Tenneco Contact      
Steve Blow
sblow@tenneco.com
(517) 262-0655

SOURCE Tenneco Inc.